How many rolls for your slab?
Add up the length of every joint. We add 10% for overlaps and tear-offs and show the rolls.
Count every seam between plywood sheets or steel plates – across the slab, along beam sides and around column boxes. Tip: plywood sheets are usually 8 × 4 ft, so a slab has a seam roughly every 4 ft one way and every 8 ft the other.
- No slurry leaks at the joints
- Cleaner slab underside
- Plywood & steel plates
- Tears by hand
- 40 m & 100 m rolls
- Prepaid · free delivery
Drag to compare
What the slab looks like when the props come out
Wherever two sheets of plywood or two steel plates meet, wet concrete pushes its cement slurry out through the gap. When the shuttering is removed you see it: rough fins along every joint, grey stones showing where the cement ran away, stains everywhere below.
Tape the joints before the steel goes in and the slurry stays in the slab. The underside comes out smoother – less hacking and filling before plaster.
Slurry leaks make weak concrete
Side by side: a slab poured without tape and one with BuildingShop shuttering tape on every joint.
Which pack for your job?
Tap your job – we show the right roll length and pack.
One house roof slab
40 m × 8 or 12 rolls
Enough for a typical single-floor slab with a few spare rolls for beams.
Shop this →
Contractor – several slabs
100 m × 12 rolls
Our most popular pack. Fewer roll changes on big slabs and steel-plate shuttering.
Shop this →
Columns, beams & small repairs
100 m × 4 rolls
A small pack for column boxes, beam sides and touch-ups.
Shop this →
Builder stocking the site store
40 m × 24 rolls
Lots of handy 40 m rolls to hand out to every gang.
Shop this →
Three steps before the pour
No tools, no mixing.
1. Clean
Sweep dust, water and oil off the joint. Tape grips best on clean, dry shuttering.
2. Tape
Press the tape along the full length of every joint, overlapping roll ends a little. Tears by hand.
3. Pour
Place steel and concrete as usual. Peel the tape off when you de-shutter.
Tape vs the usual site fixes
What sites stuff into joints – and what happens when concrete hits it.
| Feature | Recommended
BuildingShop shuttering tape
|
Cement-bag paper / newspaper |
Loose plastic sheet |
|---|---|---|---|
| Closes the joint gap | ✓ | Partly | ✕ |
| Stays put while concrete is vibrated | ✓ | ✕ | ✕ |
| Smoother slab underside | ✓ | ✕ | ✕ |
| Leaves bits stuck in the concrete | No | Yes | Often |
| Quick to apply | ✓ | ✕ | ✓ |
Shuttering tape: what sites get wrong
Questions supervisors ask us.
MythCement-bag paper in the gap does the same job.
FactPaper soaks up water, slurry seeps through it and pieces stay stuck in the slab underside.
MythSmall leaks don't matter – plaster will hide them.
FactLeaked joints leave fins and honeycomb patches that have to be hacked off and filled before plaster. That is extra labour and material.
MythTape is only for plywood.
FactIt is used on steel shuttering plates too – and on beam and column formwork.
MythIt will stick on wet or oily shuttering.
FactTape needs a clean, dry joint. Wipe it first – especially after shuttering oil has been applied.
MythOne or two rolls are enough for a house slab.
FactEvery seam counts. Measure total joint length and use the calculator above.
Where it goes on site
Every joint that wet concrete can push through.
How shuttering tape works
Seal, pour, de-shutter – what happens at every joint.
Product details
Seal every formwork joint before you pour
Wet concrete is mostly cement slurry. Wherever two plywood sheets or steel plates meet, that slurry finds the gap and runs out. What is left behind is a slab underside with rough fins along every joint, honeycombing where the stones lost their cement, and stains on the props below. Your plaster contractor then spends days hacking and filling.
BuildingShop shuttering tape closes those gaps. Run one strip over each joint on clean, dry shuttering, place the steel, pour – the slurry stays in the slab where it belongs.
Why sites use it
- No slurry leaks – joints stay sealed while concrete is poured and vibrated.
- Cleaner slab underside – fewer fins and honeycomb patches to hack and fill before plaster.
- Plywood and steel plates – for slabs, beams and column boxes.
- Bright yellow – the supervisor can see at a glance which joints are done.
- Fast – tears by hand, no tools, no mixing.
How to use
- Clean – sweep dust, water and oil off the joint.
- Tape – press the tape down along the full joint, overlapping the ends a little.
- Pour – place steel and concrete as usual. Peel the tape off when you de-shutter.
Packs
100 m rolls in packs of 4, 8 and 12. 40 m rolls in packs of 8, 12 and 24. Pick roll length and rolls per pack above.
| Brand | BUILDINGSHOP |
|---|---|
| Type | Shuttering / concrete tape (BOPP) |
| Colour | Yellow |
| Packs | 100 m × 4/8/12 rolls; 40 m × 8/12/24 rolls |
| Used for | Slab, beam and column formwork joints |
| Surface | Plywood and steel shuttering plates |
| Apply on | Clean, dry shuttering |
| Removal | Peel off when de-shuttering |
What is shuttering tape used for?
It is stuck over the joints of plywood or steel formwork before a slab, beam or column is cast, so cement slurry cannot leak out through the gaps.
How much tape do I need?
Add up the length of every joint in your shuttering (in metres) and add about 10% for overlaps and tear-offs. The calculator on this page does the maths and shows how many 40 m or 100 m rolls that is.
40 m or 100 m rolls – which should I buy?
40 m rolls suit small house slabs and repair jobs. 100 m rolls mean fewer roll changes on bigger slabs and are the most popular choice with contractors.
Does it stick on wet or oily shuttering?
Apply it on clean, dry shuttering for the best grip. Wipe water, dust or oil off the joint first.
Can I reuse the tape?
No. Peel it off when you remove the shuttering and use fresh tape for the next pour.
Can I use it for anything else on site?
Yes – marking, bundling and site packing – but it is made for sealing formwork joints.
How do I pay? Is cash on delivery available?
Prepaid only – UPI, debit/credit cards and net banking. Cash on delivery is not available.
Free delivery across India. Most orders reach you in 3–7 working days, depending on your pincode.
Payment: prepaid only – UPI, debit/credit cards and net banking. Cash on delivery is not available.
Bulk or GST invoice? Message us on WhatsApp before ordering.
Complete your slab
PP fibre for the concrete, pump primer for the pipeline, a rebar tying tool and a tarpaulin for curing.
Shuttering several slabs? Get site pricing
Contractors and builders get special rates on 100 m roll packs.
- Volume pricing on 12 × 100 m and 24 × 40 m packs
- GST invoice for your business
- Priority dispatch for pour dates

Customers also viewed
Shuttering Tape for Slab – Yellow Concrete Tape for Plywood & Steel Formwork Joints | 40 m & 100 m Rolls
From
Sale price
Rs. 659
Regular price
Rs. 1,319








